Parts Identification

Here's where to ask questions and get answers

Parts Identification

Postby John » Mon Jan 20, 2020 1:28 pm

Can someone tell me which fork tube caps are correct for a 1954 ST 165 as well as which oil cups would be correct? I also took a couple of pictures of two parts that I don't know what they are for. I don't think they are for my bike. Can anyone ID them for me?
Attachments
Unkown Parts.JPG
Unkown Parts.JPG (322.36 KiB) Viewed 3350 times
Unknown Parts 2.JPG
Unknown Parts 2.JPG (319.59 KiB) Viewed 3350 times
Fork Tube Caps.JPG
Fork Tube Caps.JPG (318.93 KiB) Viewed 3350 times
John
 
Posts: 13
Joined: Thu Mar 07, 2019 11:11 am
Location: Western Pennsylvania

Re: Parts Identification

Postby Mutt » Mon Jan 20, 2020 4:05 pm

The short cup and the flat top is used from 1952 to 1954
Mutt
 
Posts: 256
Joined: Sat Jun 02, 2018 10:11 am

Re: Parts Identification

Postby John » Fri Jan 24, 2020 12:57 pm

Can anyone tell me what the small round hole in my fork stem is for on my 1954 ST-165?
Attachments
Fork stem.JPG
Fork stem.JPG (324.59 KiB) Viewed 3267 times
Fork Stem 2.JPG
Fork Stem 2.JPG (319.79 KiB) Viewed 3267 times
John
 
Posts: 13
Joined: Thu Mar 07, 2019 11:11 am
Location: Western Pennsylvania

Re: Parts Identification

Postby Mutt » Fri Jan 24, 2020 1:27 pm

there should be a 3/16" diameter peen peened into both ends of the neck stem. Other wise, your handlebars will just spin no matter how tight you tighten the pinch bolt
Mutt
 
Posts: 256
Joined: Sat Jun 02, 2018 10:11 am

Re: Parts Identification

Postby John » Fri Jan 24, 2020 10:34 pm

Mutt, I see no sign of these drive pins or peens in any of my three parts books. Is there a part number for these?
John
 
Posts: 13
Joined: Thu Mar 07, 2019 11:11 am
Location: Western Pennsylvania

Re: Parts Identification

Postby Mutt » Sat Jan 25, 2020 12:26 am

There is no part number. Get yourself a 3/16” solid steel round head rivet about 1 1/2” long and cut ya a piece off of it about .015” longer than the stems diameter, the push it into the neck stem and peen both ends so it can’t come out Easy job, just need a ball peen hammer
Mutt
 
Posts: 256
Joined: Sat Jun 02, 2018 10:11 am

Re: Parts Identification

Postby John » Thu Jan 30, 2020 9:41 pm

I need some help identifying the correct parts to use on my 1954 ST-165 on three items. Also, after identifying the correct parts for my 1954 could you let me know what year the other parts are for?
Attachments
Muffler clamps.JPG
Muffler clamps.JPG (316.41 KiB) Viewed 3128 times
Shifter arms.JPG
Shifter arms.JPG (313.74 KiB) Viewed 3128 times
John
 
Posts: 13
Joined: Thu Mar 07, 2019 11:11 am
Location: Western Pennsylvania

Re: Parts Identification

Postby Mutt » Thu Jan 30, 2020 10:23 pm

u bolt muffler clamp used on all low pipe models from 1957 onward. single lip exhaust port clamp used on 1955 and later all models. Shifter on the left (-58) was used on all models from (some say)1960 but all swingarm models for sure. Lever on right (if it has splines) is for the 52-54 S & ST models, if it is smooth bore, it if for 1955-1959 models
Mutt
 
Posts: 256
Joined: Sat Jun 02, 2018 10:11 am


Return to HELP with Restoration and Running

Who is online

Users browsing this forum: No registered users and 5 guests

cron
Fatal: ./cache/ is NOT writable.