rod bearing fitting

Here's where to ask questions and get answers

rod bearing fitting

Postby billc » Sat Jul 20, 2019 10:39 am

What is the dia of the std 165 rod rollers ? .250 ?
billc
 
Posts: 50
Joined: Thu Feb 14, 2019 9:06 pm

Re: rod bearing fitting

Postby Mutt » Sat Jul 20, 2019 12:46 pm

yes. .250"
Mutt
 
Posts: 452
Joined: Sat Jun 02, 2018 10:11 am

Re: rod bearing fitting

Postby billc » Sat Jul 20, 2019 3:00 pm

Thank you Sir. Maybe you can answer another question I have about this lower end . I've never built one of these motors before so I'm reading all I can and feeling my way along. When I took it down there were shims behind the gen side bearing, shims behind the sprocket inner bearing (both sets of shims were between the bearing and the flywheels) and shims behind the output sprocket. If I'm reading the manual right there should only be shims behind the sprocket ? The shims total .055 in thickness . I test fitted the left flywheel into the case with new bearings and put all the shims behind the sprocket and obtained an end play of .002 . Is it normal to have shims on the crank assembly besides the ones behind the sprocket ?
billc
 
Posts: 50
Joined: Thu Feb 14, 2019 9:06 pm

Re: rod bearing fitting

Postby Mutt » Sat Jul 20, 2019 4:39 pm

shims between the left outer bearing and seal housing on 1948-54 models, behind the sprocket on all models 1955 thru 1962 models and shims behind sprocket and between flywheels and bearings on the 63 to 66 models
Mutt
 
Posts: 452
Joined: Sat Jun 02, 2018 10:11 am

Re: rod bearing fitting

Postby billc » Sat Jul 20, 2019 6:40 pm

it's a 55 st but it was raced and somebody has been in it. it sounds like it was shimmed like the 63-66 models . what was the reason behind the change in 63 ? did the flywheels change with the 175 ? what was different internally on the 175s ?
billc
 
Posts: 50
Joined: Thu Feb 14, 2019 9:06 pm

Re: rod bearing fitting

Postby Mutt » Sat Jul 20, 2019 10:55 pm

the thickness of the flywheels. 64 to 66 used compression plates with 2 holes (instead of the 48-63 type with just a center hole)
Mutt
 
Posts: 452
Joined: Sat Jun 02, 2018 10:11 am

Re: rod bearing fitting

Postby billc » Sun Jul 21, 2019 1:04 am

Ah soo.... i see. OK, one last question and i'll leave you alone ;-) I see in the parts book it gives 3 different part #s for the 3 crank bearings. It looks like the generator side uses a sealed bearing ? Is it sealed on both sides ? The two sprocket side bearings look identical and aren't sealed . They look the same but have two different #s . ???? And lastly, apart from the sealing, they have the same width, i.d. and o.d. so can you use 3 identical sealed bearings and remove the seals from two of them ? Thanks.
billc
 
Posts: 50
Joined: Thu Feb 14, 2019 9:06 pm

Re: rod bearing fitting

Postby Mutt » Sun Jul 21, 2019 8:51 am

the 48-54 models all used 3 open bearings (no seals) the 55-66 models used 2 open bearings and the gen/mag side used a bearing with only one side sealed The seal goes towards the gen/mag. Running sealed bearings is not recommended, as when the grease goes away (and it does) you will be running dry bearings
Mutt
 
Posts: 452
Joined: Sat Jun 02, 2018 10:11 am

Re: rod bearing fitting

Postby billc » Sun Jul 21, 2019 9:51 am

Thanks Mutt, I think I can take it from here. I can't wait to ride this little guy :-)
Attachments
20190715_170316.jpg
20190715_170316.jpg (442.51 KiB) Viewed 9414 times
billc
 
Posts: 50
Joined: Thu Feb 14, 2019 9:06 pm


Return to HELP with Restoration and Running

Who is online

Users browsing this forum: No registered users and 30 guests